EBWGP Knife-Gate-Valve pneumatic single acting with spring return:
Advice
The products descript in this documentation in the conditions of our delivery are partly completed machinery according to annex 2 paragraph g of the directive 2006/42/EC on machinery, which must not be put into service until the final machinery into which it is to be incorporated has been declared in conformity with the provisions of the Directive 2006/42/EC on machinery, where appropriate. Please take notice to the Declaration of incorporation and the assembly instruction.
EBWGP Knife-Gate-Valve pneumatic double acting:
Installation
All knife-gate valves should be installed vertically up to max. 45° to the vertical. For other installation positions e.g. horizontally it is necessary to ensure that especially for larger diameters and actuators no bending stress appear at the stem/top- bridges, piston- stem etc., otherwise the function of the actuator and the tightness of the valve is not guaranteed. In such cases protective features are definitely needed.
A hanging installation of the knife-gate vale must be avoided!
Advice
The products descript in this documentation in the conditions of our delivery are partly completed machinery according to annex 2 paragraph g of the directive 2006/42/EC on machinery, which must not be put into service until the final machinery into which it is to be incorporated has been declared in conformity with the provisions of the Directive 2006/42/EC on machinery, where appropriate. Please take notice to the Declaration of incorporation and the assembly instruction.
EBWGP Knife-Gate-Valve pneumatic single acting with spring return:
normally closed
DN50 … DN300
SPECIFICATION:
DESIGN
Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B - PN10 (former DIN 2501). ANSI 150 on request.
MEDIA
Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam.
BODY
- GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min)
- stainless steel 1.4408
SEALING
(FKM or PTFE on request)
GLAND
3-piece sealing set:
- 2x synthetic fibre, PTFE-coated
- 1x NBR-, EPDM or FKM-ring
KNIFE
Stainless steel 1.4301 or. 1.4401 (304 or 316)
STEM
Stainless steel 1.4305 or 1.4404 (304 or 316)
FUNCTION
Pneumatic single acting with spring return, normally closed (NC).
PRESSURE DISCHARGE
One-sided, two-sided on request
PILOT PRESSURE
6 bar
PILOT MEDIA
Filtered, slightly oiled air (subject to remaining oil, dust and water). According at least to ISO 8571, ISO 8573 or PNEUROP 6,661.
PRESSURE RANGE
Please refer to the table
TEMPERATURE RANGE
- metal: on request
- NBR: -25°C ... +90°C
- EPDM: -35°C ... +120°C
Attention: Temperature range not for all media.
FACE TO FACE
EN 558-1 Row 20
INSTALLATION
Only with vertical upwards actuator
The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice!
EBWGP Knife-Gate-Valve pneumatic double acting
DN50 … DN400
SPECIFICATION:
DESIGN
Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B - PN10 (former DIN 2501). ANSI 150 on request.
MEDIA
Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam.
BODY
- GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min)
- stainless steel 1.4408.
SEALING
(FKM or PTFE on request)
GLAND
3-piece sealing set:
- 2x synthetic fibre, PTFE-coated
- 1x NBR-, EPDM or FKM-ring
KNIFE
Stainless steel 1.4301 or. 1.4401 (304 or 316) STEM Stainless steel 1.4305 or 1.4404 (304 or 316) FUNCTION Pneumatic double acting
PRESSURE DISCHARGE
One-sided, two-sided on request
PILOT PRESSURE
6 bar (lower pressure on request)
PILOT MEDIA
Filtered, slightly oiled air (subject to reamaining oil, dust and water). According at least to ISO 8571, ISO 8573 or PNEUROP 6,661.
PRESSURE RANGE
Please refer to the table
TEMPERATURE RANGE
- metal: on request
- NBR: -25°C ... +90°C
- EPDM: -35°C ... +120°C
Attention: Temperature range not for all media.
FACE TO FACE
EN 558-1 Row 20
The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice!